Hydroponics Online Store



Hydroponic Systems

Hydroponic Grow Lights & Bulbs

Hydroponic Tents & Grow Boxes

Hydroponic Ballasts

Grow Light Reflectors

Hydroponic Nutrients

Grow Media Rocks

Hydroponic Pumps

Hydroponic Pots

Hydroponic Books

Meters

Hydroponic Exhaust Fans

Hydroponic Seeds

Hydroponic Foggers

Home Store Blog Forums FAQs Lesson Plans Pictures


Search:



8VOLT 300MA RAW REPLACEMENT LAMP FITS SANSUI KENWOOD OTHERS For Sale


8VOLT 300MA RAW REPLACEMENT  LAMP FITS SANSUI KENWOOD  OTHERS
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.



Buy Now

8VOLT 300MA RAW REPLACEMENT LAMP FITS SANSUI KENWOOD OTHERS:
$7.95

8 VOLT 150 TO 300MARAW 8.5MM LED REPLACEMENT FORPIONEER SANSUI KENWOODOTHERS .

USED IN KENWOOD6600,7600,9600,8005,9940,OTHERS.

THIS STYLE STANLEY RUBBER BASE BULB PUSH FITS OVER 2 PINS AS SHOWN IN PICTURES. PIN SPACING IS 13 TO 14 MM CENTER TO CENTER(SLIGHTLY OVER 1/2 INCH).THESE LONG LASTING HIGH OUTPUT (100,000 TO 140,000 MCD @ 100 MA) 8.5MM LED CIRCUIT RAW REPLACEMENTS HAVE AN AVERAGE LIFESPAN OF 100,000 HRS.THE AVERAGE INCANDESCENT BULB LIFESPAN IS 1000 HRS.REINSTALLINTO EXISTING LAMP BASE USING A PAIR OF NEEDLE NOSE PLIERS. CIRCUIT REGULATION BUILT INTOLED LEADS. LED INCORPORATES 5 SEPARATE CHIPS AND DRAWS AROUND 50 MA.LED LEADS CAN BE BENT TO MAKE A 90 DEGREE LAMP USED IN SANSUI THESE WIDE DISPERSION STRAW HAT LED BULBS ARE AVAILABLE IN WHITE (140K MCD), WARM WHITE(40 lm), BLUE(180K MCD), GREEN(100K MCD), RED(100MCD), AND ULTRA-VIOLET(30K MCD). SEE PICS. AS ALWAYS, THANKS FOR LOOKING.

NOTE: PRICE APPLIES TOONE RAW 8 VOLT AC LED REPLACEMENT BULB TO BE USED IN YOUR RECYCLEDSTANLEY RUBBER BASE.PLEASE SPECIFYCOLOR ON ORDER OR BY E-MAIL TO AVOID DELIVERY DELAY. I WILL NOT ASSEMBLE OR SHIP WITHOUT THIS INFORMATION.


Lamp Information

Harman/Kardon Citation 18
The very small bulb that lights the \"In Tune\" indicator and the \"Stereo\" indicator is a 12 volt 35 milliamp type

Kenwood 600T and 650T

8 volt 300 milliamp X 5 bulbs (two for dial and one for each of the meters) X 5 green-tinted bulbs with rubber grommet base and wire leads Kenwood 600T and 650Tfor dial and one for each of the meters)

Kenwood KR-5400
Meters and dial use 8 volt 200 milliamp X 5 bulbs with rubber grommet base and wire leads.

Kenwood KR-7600 receiver
Dial uses 8 volt 300 milliamp X 6 bulbs with rubber base that push over two pins, same as the Sansui TU-717. Meters use 8 volt 200 milliamp X 4 frosted bulbs with rubber grommet base and wire leads. Button indicator lamps - 8 volt 50 milliamp t1.75 grain of wheat bulbs.

Kenwood KR-9600 receiver
Dial uses 8 volt 300 milliamp X 6 bulbs with rubber base that push over two pins, same as the Sansui TU-717. Meters use 8 volt 200 milliamp X 4 frosted bulbs with rubber grommet base and wire leads. Button indicator lamps - 8 volt 50 milliamp t1.75 grain of wheat bulbs.

Kenwood KR-x500 and KR-x600 receivers

8 volt 200 milliamp bulbs with rubber grommet base and wire leads, and 8 volt 300 milliamp bulbs with rubber base that push over two pins.

Kenwood KT-80
8 volt 50 milliamp X 1 (power switch cap)

Kenwood KT-615
8 volt 50 milliamp X 1 (stereo indicator)
12 volt 150 milliamp X 2 - Physically the same as those used in the KT-815 (8 volt 300 milliamp).

Kenwood KT-815 and KT-8155
Dial and Meters use 8 volt 300 milliamp X 4 green-tinted bulbs with rubber grommet base and wire leads.

Kenwood KT-917
8 volt 300 milliamp X 5 identical to those in the 600T.

Kenwood KT-1000
8 volt 150 milliamp X 1
8 volt 50 milliamp X 2 (stereo and lock indicators)

Kenwood KT-5500
8 volt 300 milliamp X 2 green-tinted bulbs with rubber grommet base and wire leads - one for dial and one for meters.

Kenwood KT-6005 and KT-6007
Dial uses 8 volt 300 X 4 milliamp bulbs with rubber base that push over two pins, same as the Sansui TU-717.

Kenwood KT-6500 and KT-6550
8 volt 300 milliamp X 3 green-tinted bulbs with rubber grommet base and wire leads - two for dial and one for meters.

Kenwood KT-7000 and KT-7001:
8 volt, 250 milliamp X 7 fuse type.. Upper and lower indicators (AM, FM, Mute, MPX) are 8 volt, 150 milliamp bayonet base.. The KT-7000 stereo indicator light is \'special\' -- it is an 8 volt, 30 milliamp miniature.

Kenwood KT-7001
8 volt, 300 milliamp X 6 (fuse type, meters and illumination) 8 volt, 150 milliamp X 2 (bayonet type, Muting and MPX) 8 volt, 40 milliamp X 3 (miniature, AM, FM, Stereo)

Kenwood KT-7300
8 volt 300 milliamp X 3 green-tinted bulbs with rubber grommet base and wire leads - two for dial and one for meters.

Kenwood KT-7500 and KT-7550
8 volt 300 milliamp X 3 green-tinted bulbs with rubber grommet base and wire leads - two for dial and one for meters.

Kenwood KT-6005 and KT-6007
Dial uses 8 volt 300 milliamp X 4 bulbs with rubber base that push over two pins, same as the Sansui TU-717.

Kenwood KT-8300
8 volt 300 milliamp (fuse type)

Luxman T-110
Dial lamps - 4 \"bayonet style\"
A #53 bulb .

Marantz 120
Dial lamps - 8 volt, 200 milliamp (fuse type)
Dial pointer lamp - 8 volt, 0.06 amp
Meter lamp - 8 volt, 0.2 amp
Selector indicators - Bi-pin 6.3 volt or 8 volt, 0.04 amp

Most Marantz tuners from the 1970s (including models 120, 150, 115B and 2120) use the same fuse-type, 8 volt, 180-200 milliamp dial illumination lamps.

Marantz receivers
Most 2200 Series Marantz receivers used an 8 volt 200 milliamp lamp for the tuning dial and an 8 volt 300 milliamp lamp for the two meters. The 2265B uses five lamps behind the tuning dial and one lamp each behind the signal-strength and tuning meters. The lamps run on AC from an 8-volt transformer winding. The bulbs, known as fuse lamps, look like 3AG fuses and are socketed in fuse holders.

Philips AH673 and AH6731
6.3 volt 40 milliamp X 3, 1/4 mini bayonette type (\'GE 1302\' bulb)
There are 13 of them in the tuner, 16 in the preamp and another 4 in the amp for this series.

Pioneer TX-7500
Dial illumination: 8 volt 300 milliamp \"wedge type\" lamps
Pilot (\"power\") and stereo indicators: 6 volt 30 milliamp X 2 \"grain type\" lamps with leads

Pioneer TX-9100
Tuning and signal-strength meter illumination lamps: 8 volt 300 milliamp.
AM, FM, stereo indicator and pointer: 40 milliamp (not sure of the voltage).

Pioneer TX-9500II
8 volt 300 milliamp X 4
8 volt 50 milliamp X 1
6 volt 30 milliamp X 3

Pioneer TX-9800
8 volt 300 milliamp
6 volt 50 milliamp

Realistic TM-1001
8 volt 250 milliamp X 3
PL1: BF311-03030A 8V, 250 milliamp
PL2 and PL3: BF310-03030A 8V, 250 milliamp
The first one lights up the tuning dial and the bottom two light up the signal meter and multipath meter.

Sansui TU-217
No dial lamps used

Sansui TU-317
Dial uses 8 volt 300 milliamp X 3 bulbs with rubber base that push over two pins.

Sansui TU-417, TU-517, TU-519, TU-710, TU-717, TU-719, TU-919, TU-5900 and TU-9900
Dial uses 8 volt 300 milliamp X 4 bulbs with rubber base that push over two pins.

Sansui TU-7500
Stereo indicator lamp PL 010: 7 volt, 0.1 amp
FM/AM indicator lamps PL 007/008: 7 volt, 0.1 amp
Dial pointer lamp PL 009: 6 volt, 75 milliamp
Meter lamps PL 005/006: 6.3 volt, 0.25 amp

Sansui G-4700, G-5000, G-9000 and most (if not all) G-series receivers use the same bulb: 8 volt 200 milliamp bulb with rubber grommet base and wire leads.

Sansui TA-300 and TA-500 receivers
Although these receivers appear to have a TU-717 style case and face, they use different dial bulbs The bulbs in the TA-300/500 are wire leaded. They are 8 volt 300 milliamp like the TU-717 etc., but are not the push-on bulbs.

Sony ST-A6B:
Meters: bulbs say \"6.3V .
Dial: 8 volt 300 milliamp X 3, \"wedge base\" bulbs.

Technics ST-9030
6.3 volt 40 milliamp X 2 (stereo and wide IF indicators)
6.3 volt 250 milliamp X 5 (fuse type)

Yamaha T-1
14.5 volt 80 milliamp X 4 (wire-ended, clear bulbs)

Yamaha T-2
14.5 volt 80 milliamp X 4 (wire-ended, clear bulbs)


Buy Now


 

Hydroponic Forum Discussions:


Popular Hydroponic Items: