Hydroponics Online Store



Hydroponic Systems

Hydroponic Grow Lights & Bulbs

Hydroponic Tents & Grow Boxes

Hydroponic Ballasts

Grow Light Reflectors

Hydroponic Nutrients

Grow Media Rocks

Hydroponic Pumps

Hydroponic Pots

Hydroponic Books

Meters

Hydroponic Exhaust Fans

Hydroponic Seeds

Hydroponic Foggers

Home Store Blog Forums FAQs Lesson Plans Pictures


Search:



Clear Coat Table and Bar Top Epoxy Coating, 1 gallon For Sale


Clear Coat Table and Bar Top Epoxy Coating, 1 gallon



This item has been shown 6137 times.

Buy Now

Clear Coat Table and Bar Top Epoxy Coating, 1 gallon:
$52

KLEERKOTE TABLE TOP EPOXY KIT

1/2 Gallon Resin and 1/2 Gallon Hardner

Overview: This product is a 100% solid, two component, clear polymer coating that is
mixed at a 1 to 1 ratio by volume. Each kit contains a bottle of resin and
a bottle of hardener. The product cures to a clear, high build, glass like
finish that resists scratching, yellowing and will not distort with age.
Items coated with it will become permanently preserved and protected for your
enjoyment throughout a lifetime. This product will not exhibit blushing or
sweat out under high humidity conditions

Primary use:This product is commonly seen on bar tops and table tops in many bars and
restaurants.

Application:The product should be applied in two stages to clean surfaces. The first stage
is referred to as the seal coat. The seal coat is brushed on in a thin layer
and is used to seal any pores in the surface and prevent air bubbles from
forming in the following flood coats. This stage is followed by the flood
coat, which will flow and self level, clean brushes or squeeges can be used
to help spread the epoxy. Flood coats are applied in 1/8" layers at a time,
as many as desired can be applied, however one to three coats is average for
most table or bar coatings.

Recoating/Between Layers:Recoating can usually be be done within 4 to 8 hours. If re-coated within this
time period no sanding is necessary between layers. If your previous
layer has fully dried, light sanding with 220 or 320 grit sandpaper is
recommended to achieve good bonding surface. After sanding you should wipe down
with a solvent such as denatured alcohol, acetone orlacquer thinner to
remove any impurities from the surface. (do NOT use mineral spirits)

Imbedding Pictures:Objects, such as pictures, maps etc. can be imbedded in this product during the
pours. Most photo quality paper does not require any special preparation
however sometimes thin paper objects must first be sealed with a white glue or
similar product to prevent the kleer koat from fully penetrating the paper and
causing it to become transparent.

Imbedding Solid Objects (wood, rocks, shells, etc.)All porous materials should first have a seal coat of epoxy applied. This will prevent
air bubbles from occurring in subsequent flood coats. Usually the objects can be set
in place before sealing.

Working Conditions:For best results the product should be used at temperatures from 70-80 degrees F.
The room which you are working should be clean, dry, dust and insect free.
Settling dust can often cause blemishes on the glassy surface.

Exterior Applications:Please not that although this product will resist yellowing better than other epoxies
it is NOT 100% UV resistant. Continuous outdoor UV exposure over months or years
will cause the finish to lose its gloss and cause gradual changes in color.

Coverage:See the coverage charts shown below to calculate the amount you will need for your
area. Remember not to combine seal and flood coat coverage's. Flood coats are
designed to go on approximately 1/8" thick, which is about three times thicker
than that of a seal coat. Example: A 6ft x 4ft bare wood table (24sq ft) would
require 2 Quarts to complete ONE seal coat and about a gallon and a half to complete
ONE flood coat for a total of Two Gallons.

Beginners Notes:This material leaves professional results when applied correctly so take your time and
make sure to beware of these of the common problems we have seen encountered by
first time users.

1. Always make sure that your mixing container is clean and your measuring device is
accurate, this product REQUIRES that you mix at a 1 to 1 ratio by weight or volume,
any variances from this can cause the epoxy to stay soft and not fully cure.

2. This product requires a THOROUGH mixing, usually between 3-4 minutes of solid mixing
without excessive whipping of the mixture(whipping will put lots of air bubbles into
the epoxy). Amounts greater than one gallon at a time can require upto 6-7 minutes
of mixing.

3. After the two components are poured together and stirring begins the mixture will
turn a cloudy white color, this represents areas in which the epoxy has not fully
combined. You must continue to mix until all signs of cloudiness and tiny white lines
have completely disappeared (usually takes 3-4 minutes of
thorough mixing).

4. Always scrape the sides of your mixing container and also the stick during those
3-4 minutes. If UNMIXED epoxy remains on the side of the container or the stick it
will cause wet spots on your finished product if that UNMIXED material falls into
your project......Followup: While pouring your epoxy onto the surface NEVER scrape
the container to remove every last drop, because no matter how thorough you mix
there will always be an unmixed drop on the side of the container that will leave a
wet spot.

Recommendation of Materials Needed For Application:

Safety Gloves - Epoxy can be very sticky

Graduated Mixing Cups - An accurate measurement is extremely important to achieve
optimum curing.

CLEAN Stir Sticks - Any dirt will end up showing on your product. Mixing is very
important, if you whip while mixing you will end up with air bubbles, long thorough
stirs are required.

Applicators - Rubber squeeges are simple to use and leave no air bubbles. Foam brushes
and nylon bristle brushes are preferred with epoxy, make sure there are no loose hairs.

Hair Drier, Heat Gun or Torch - These are used after the pour is completed and the epoxy
is still liquid. A very smooth stroke across about 6-12 inches above the epoxy surface will
burst remaining air bubbles.

Our kleer kote product can be used in any of the above mentioned applications
to achieve a super hard clear finish with great depth.

Available in 2 Part Kits

Mixing Ratio By Volume: 1:1

Coverage Chart

Total Kit Size
(Combined volume of both parts) Coverage for a Seal Coat Coverage for a flood coat 2 Quarts 24 Sq Ft. 8 Sq. Ft. 1 Gallon 48 Sq Ft. 16 Sq. Ft. 2 Gallons 96 Sq Ft. 32 Sq. Ft. 4 Gallons 192 Sq Ft. 64 Sq. Ft. 16 Gallons 768 Sq Ft. 256 Sq. Ft.

" Click Here To See Other Sizes of This Product "

" Click here to send email address for step by step application guide "

" Click Here To Visit My Store " >

E-mail Me if You Don't See The Size or Quantity you want.

I Can Supply All Materials In larger Sizes and Quantities. $33.50/ gallon for order of 100 gallons or more.

Will Ship International: E-mail for shipping cost.

Also have mold making rubber, casting plastics, mold making clay in my store.


Buy Now


 

Hydroponic Forum Discussions:

Hydro pumpkins
Tomato problems
Newbie
Japanese maple tree
inductor driven fan
EXTREME Series LED 84X-PRO
Botanicare turbogarden ebb & flow 706960
lables
High PH
uninteruptable power supply (ups)
yellow leaf
What is this on my cucumber seedlings?
no medium nft, can bottom of stem touch steam?
avoid stem rot rockwool
Water
Efficiency
PPM meter Hanna HI98308
Is this root rot or beneficail fungi growth?
Noob looking at a "dual-mode" system
topwater feeding with DWC when starting?

Popular Hydroponic Items:


30mm Hot Cute Bling Lt. Pink Mickey Diy Resin Plastic Deco Craft Cell Phone 5 Pc picture
30mm Hot Cute Bling Lt. Pink Mickey Diy Resin Plastic Deco Craft Cell Phone 5 Pc


30mm Hot Cute Bling Lt. Pink Mickey Diy Resin Plastic Deco Craft Cell Phone 10pc picture
30mm Hot Cute Bling Lt. Pink Mickey Diy Resin Plastic Deco Craft Cell Phone 10pc


30mm Cute Hot Bling Lt Pink Mickey Diy Resin Plastic Deco Craft Cell Phone 20pc picture
30mm Cute Hot Bling Lt Pink Mickey Diy Resin Plastic Deco Craft Cell Phone 20pc


50 Pcs Mix Cabochons Flatback Bundle Roses Cupcake Cookies Bow Chocolate Snacks picture
50 Pcs Mix Cabochons Flatback Bundle Roses Cupcake Cookies Bow Chocolate Snacks


Molds-moldes Para Hacer Paletas De Bombon Gelatina,chocolate Etc (1.5in X 1.5in) picture
Molds-moldes Para Hacer Paletas De Bombon Gelatina,chocolate Etc (1.5in X 1.5in)


100pcs Angel Flat Back Resin Diy Mobile Phone Case Shell Decoration  Angel 2014 picture
100pcs Angel Flat Back Resin Diy Mobile Phone Case Shell Decoration Angel 2014


100 Flat Diy Phone Decoration Cosmetic Accessories Resin Strawberry Drawing 2014 picture
100 Flat Diy Phone Decoration Cosmetic Accessories Resin Strawberry Drawing 2014


100 Pcs Flat Back Resin Bow Tie Diy Mobile Phone Case Shell Decoration Cosmeti picture
100 Pcs Flat Back Resin Bow Tie Diy Mobile Phone Case Shell Decoration Cosmeti


150pcs Sparkling Flatback Resin Diy Mobile Phone Case Shell Decoration Cosmetic  picture
150pcs Sparkling Flatback Resin Diy Mobile Phone Case Shell Decoration Cosmetic


Sport Theme Baseball&football Flexible Polymer Clay Resin Push Mold  picture
Sport Theme Baseball&football Flexible Polymer Clay Resin Push Mold