This is a HAAS VF-0 CNC Vertical Milling Center with LOW USAGE HOURS! (Our 6th picture has the total used hours broken down where total used means from when it was purchased brand new from the factory)
BEWARE:if you are interested in knowing the total hours of a machine and are shown or told what\'s listed on the screen in our last picture (Power on time, Cycle start time, and Feed cutting time) it could be incorrect. That screen is for knowing those times for a specificpiece or pieces one is working onand can be easily ZEROED out.
This machinealso comes with the original HAAS Manual, Lance Co. Pre-Installation Guide, and all service reports dating back to 11/3/1994 when the machine was first started up.
Itwas RECENTLY INSPECTED and is RUNNING GREAT!!
Mechanical Specification
GENERAL:
MODEL
VF-0
SERIAL NUMBER
2777
DATE OF MANUFACTURE
2/1994
APPROX. DIMENSIONS (H x W x D)
106\" x 88\" x 92.8\"
APPROX. WEIGHT
6,500 LBS
COOLANT FLOW RATE
2 GPM
COOLANT CAPACITY
20 GAL.
AIR REQUIRED
4 SCFM / 100 PSI.
POWER REQUIRED
25 AMP
TABLE:
TABLE SIZE (L x W)
26\" x 14\"
MAX. TABLE LOAD (EVENLY DISTRIB.)
750 LBS
T-SLOTS (WIDTH / CENTER DISTANCE)
.625” / 3.94”
TRAVEL:
X AXIS TRAVEL
20\"
Y AXIS TRAVEL
16\"
Z AXIS TRAVEL
20\"
SPINDLE NOSE TO TABLE TOP
4\" - 24\"
SPINDLE:
TAPER SIZE
#40 TAPER
SPINDLE SPEEDS
0 - 7,500 RPM
TRANSMISSION
1-SPEED BELT DRIVE
RATIOS
1:1
MAX. TORQUE @ 1200 RPM
25 FT-LBS
BEARINGS
ABEC CLASS 7
BEARING LUBRICATION
AIR/OIL INJECTION
COOLING
FORCED AIR
ORIENTATION
AIR-ACTUATED SHOT PIN
TOOL CHANGER:
CAPACITY
20 STATIONS
TYPE
CT-40 OR BT-40
PULL STUD
JMBTA STANDARD 45 DEGREES
MAX. TOOL DIA. (20 TOOLS)
3.5”
MAX. TOOL WEIGHT
12 LBS
CHANGE TIME AVG. (TOOL TO TOOL)
5.0 SECONDS
CHANGE TIME AVG. (CHIP TO CHIP)
8.0 SECONDS
ACCURACY:
POSITIONING
+/- 0.0002”
REPEATABILITY
+/- 0.0001”
FEEDRATES:
RAPID TRAVERSE RATE ALL AXES
500 IPM
MAX. CUTTING FEED RATE ALL AXES
200 IPM
MOTORS:
SPINDLE MOTOR, MAX. RATING
7.5 HP
AXIS MOTORS (MAX. RATING)
3.0 HP
AXIS MOTORS (MAX. THRUST RATING)
2850 LBS
ENCLOSURE:
MATERIAL
14 GA COLD ROLL STEEL
DOOR OPENING WIDTH
35.5”
Equipped With
FULLY AUTOMATIC 20-TOOL CHANGER
7,500 RPM AIR-COOLED SPINDLE EMPLOYS BELT DRIVE
FOURTH AXIS COMPATIBLE
COOLANT NOZZLES (STANDARD SYSTEM W/ TANK & PUMP)
ALL AVAILABLE MANUALS
RS-232 PORT INTERFACE FOR DNC OPERATION
This Machine Looks & Runs GREAT!!
IT HAS LOW USAGE HOURS (LOOK AT OUR 6TH PICTURE)!!!
Machine Is Under Power So Come By and Try It!!
If you\'re interested feel free to make us an offer.
The two collet chucks w/ CAT 40 shanks inserted in the carousel in the picturesDO NOTcome with the machine. They are there for testing purposes only.
Item is soldAS SEENin photos and does not come with anything else unless specified in item description.
Buyer takes ALL RESPONSIBILITY for shipping of this item andMUST HIREa rigger to move and load the machine onto a truck. If they chose to have a shipping company come and pick up the items they are responsible for hiring them as well.
If you have any questions about the machine please call
Jason 610-279-8810