S-Horse QRP Kit HAM RADIO 20m CW QRP TRANSCEIVER - PIXIE II QRP KIT 14,060 KHz
Description
Note : this item is diy kit , wifi module
1. Introduction
This is a very small volume of simple 20 meter band micro-power amplitude telegraph
transceiver, Despite it\'s small size and DC receiver limitations, it is capable of working
several hundred miles when connected to a good 20 meter antenna. Designed by
. It provide the WIFI module, with the mobile phone application
communication. Support automatic key. Provide automatic sending function. Display
sending sequential. Provide acrylic case.
2. Specifications
Power supply: 9~13.8 Volts DC, >500mA (Recommend the use of batteries)
Antenna: 50ohm, 14MHz, SWR<2.0
Receive: static current 50mA
Transmission power: 2W
Frequency: launch the vibration frequency, 14.060MHz
Receives the local oscillator frequency: about 14.060-14.090MHz
Work mode: the CW
KEY: Manual and automatic auto-detection
Automatic sending: ok
Config: the mobile phone application(WIFI)
Case: acrylic
3. Circuit principle
Reference schematic diagram. Receiving part is the core of a NE602, inside it includes
an oscillating circuit an a balanced mixer, antenna in the signal after a crystal filter, into
the mixer, oscillation circuit at the receiving frequency oscillation, two signals through mixing,
directly put the CW signal frequency conversion for audio,NE602 output again gave
LM386 audio amplifier, thus complete the receiving process. Circuit consisting of Q4 audio oscillator
to produce about 700Hz sine wave side tone,LM386 amplification, make the headset
with \"ditick\" audio transmission. Launch part using the NE602 oscillation circuit, and then to Q6 do
the buffer amplifier, at the end of the class is made up of class C C2078 amplifier, after
amplification of the high frequency signal after LPF filtering antenna.
The WIFI module is optional. If you do not use the WIFI module, you need to short circuit
the JP1, then \"S-Horse\" == Ordinary CW radio. If you use the WIFI module, you need to
unplug the JP1, then you can use the mobile phone configuration data.
4. Component selection
8050 magnification is about 130, C2078 magnification is about 200. L4 is HFC, ferrite
beads in FT37-43 (black) to use the 0.5mm enameled wire around 8 times. L5 is the high
frequency filter inductance in T37-2 on the iron core is circular and (red) using 8 to 0.5 mm
enameled wire around.
Inductance is a fixed inductance (outsourcing black heat shrinkable casing).Other
devices, such as 0.47uf for monolithic capacitors, more than 10uf capacitance for
aluminum
electrolytic capacitors, all resistance is a quarter w fixed resistance.
5. Production process
5.1 According to the list of components, check the number of components. Have tools,
Electric iron, Solder wire, and A multimeter on hand. Take welding from low to high
order,Recommend: Resistance -> Diode -> Capacitance -> Triode -> Crystal oscillator ->
Bridgerectifier -> Electrolytic capacitor -> Ic -> Inductor -> Magnet ring -> C2078 -> Other.
6.2 Power on: Do not distinguish between positive electrode and negative
electrode(Internal rectification), Recommend the use of battery, Can also use the DC linear
voltage stabilized power supply. If power on after tens of seconds without abnormal
heating,then it\'s normal.
6.3 Listen to the base noise: Connect the 8ohm headset, after power will hear a slight
voice, then it\'s normal.
6.4 The receiving circuit test: If connect the antenna to hear the voice and do not connect
the antenna to hear the voice of a great difference,then it\'s normal.
6.5 The sending circuit test: Connect dummy load, don‘t install WIFI module, short circuit
JP1, connect the key, and power on. Now you can use the key control to send, Static
current:40~100mA,Sending current:400mA, In the sending state under the virtual load
will be fever. Note: it is not a long time to send.
6.6 The WIFI module test: Connect dummy load, install WIFI module, circuit breaker JP1,
connect the 8ohm headset, connect the key, and power on. Click “WIFI button” to open a
WIFI connection, would you hear \"ka ka\" sound, then WIFI is opened. Download the APP
from the www.lxqqfy, using APP to connect the WiFi module to communicate.
package：
1pc DIY KIT S-Horse QRP Kit HAM RADIO 20m CW QRP TRANSCEIVER - PIXIE II QRP KIT 14,060 KHzPayment
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of sale closing.
4.We ship to your or Paypal address. Please make sure your and Paypal address is correct before you pay.
Shipping
1.We ship to your or Paypal address. Please make sure your and Paypal address is correct before you pay.
2.Items will be shipped within 1-3 business day when we received payment.
3.Delivery time depends on destination and other factors;
4.International buyers please note:
a.Import duties, taxes and charges are not included in the item price or shipping charges. These charges are buyer’s responsibility. We will try our best to reduce the risk of the custom duties.
b.Please check with your country\'s customs office to determine what these additional costs will be prior to buying.
Returns policy
1.If the item is not as described or damaged in transportation, please send it back within 7 days upon date of receipt
2.For defective item, we guarantee free exchange or full refund within 30 days from the day of placing order
3.Buyers pay shipping fees at their own cost to return products for exchange or refund. We will be responsible for the postage of replacements
4.Items must be unused, in original packaging and include all parts, accessories and packaging
5.When we receive your returned item, we will investigate the situation and consider to offer replacement or refund according to the situation
Terms of sales
1. All the items will be tested before shipping. Buy them with the confidence!
2. We maintain hightest buyer ratings StarStarStarStarStar and 100% customer satisfaction, Positive response will be much appreciated from you.
3. Any dissatisfaction or problem, please contact us before you leave neutral Neutral response rating or negative Negative response rating response.
response
1.When you received package and like it, kindly comfirm received order and leave a positive response with full stars for us. Thank you.
2.Any dissatisfaction or problem, please contact us before you leave neutral Neutral response rating or negative Negative response rating response.
