Arduino IDE DIY Geiger Kit ver. 1.01with SD Logger Shield Board
RH-K-GK-1-L
Unique project for soldering, sold not assembled! Free CR1220 3V battery included for RTC!
We supply link to download all required source files, you\'ll need to solder main board and SD shield by yourself!
If you need this item fully soldered please check my other items.
This is unique hardware with open source code Geiger SDLogger project based on Arduino IDE. The kit includes main board with16x2 LCD and SD Logger Shield. SD Shield has RTC circuit (real timeclock), 3.3V level shifter for SD card, Buzzer and micro SD socket.Support connection of Adafruit GPS module or UART logging through RXTX pins. Files on SD card contains CPM readings for each data point,your local date and time, nmea geographical data and total absorbeddose. 400V high voltage for GM Tube produced with PWM.Microcontroller program correct high voltage if battery capacity istoo low. The kit makes clicker sound similar to a “classic”Geiger counter sound.
Note: Geiger Tube, Enclosure, SD Card,Battery and TTL Module are not included in the purchase! This kitrequires good soldering skills to solder SMD, additional TTL dongle for uploading firmware andability to use Arduino IDE.
Technical specifications:
Geiger Tube Compatibility: GM Tubes with anode voltage 350-550V
Arduino IDE compatible, minimum hardware for maximum performance
LCD 16x2 HD44780 (fixed properly over main board, no need to use wires)
Two tact buttons for controlling the software
Moving Average calculating algorithm
Represent dose in uSv/h or uRn/h units
UART logging with \"Radiation Logger\", require USB-TTL dongle
Adafruit GPS module support
SD Shield Board with RTC
Absorbed dose, CPM, NMEA logging
Smart Backlight Control
Fast Bargraph on LCD
Battery Indicator for Ni-MH
Clock 24 hours format
Supply Voltage: 5V DC or Battery
Supply Current: 25mA without backlight
Dimensions: 81(L) x 37(W) x 50(H) mm
Shipping Weight: 250gr
SKU: RH-K-GK-1-L
Radiation SD Logger based on Atmega-328and programmed with Arduino IDE. SD Shield has SMT parts that requiregood soldering skills! Atmega microcontroller comes with Arduino IDEbootloader, but you need to upload supplied sketches by yourself.
The main benefit of this kit is SDLogger Shield. It support micro SD Cards with capacity 2Gb-8GB.Radiation data stored with 3 files. Each time you starting thecounter, it will create a new log files and the older files stay safeon card. Up to 100 files can be created before you need to clear SDmemory. LOG.CSV store CPM readings for each data point. The file canbe opened with our \"Radiation Logger\" Windows applicationfor building graph or with any csv editor. LOG.TXT store local dateand time, CPM, aborbed dose accumulated since last minute and batteryvoltage. If GPS module connected, LOG.TXT will also store NMEAgeographical data. DOSE.TXT file keeps only total lifetime absorbeddose. User manual describes an example how you can export nmea datato google map and add CPM readings to the map.
The software and hardware wheredesigned to produce tube high voltage with PWM technology. Noadditional IC\'s required, everything is controlled with software. Bydefault it programmed to 400V-420V and you can make fine adjustthrough software calibration from 350V to 480V. If required, the kitcan be adjusted for 500V-550V. For higher voltage it possible to make600V hardware mode with voltage multiplier.
When using batteries for powering thecounter, you do not have to worry about tube voltage drops because oflow battery, microcontroller will correct high voltage if yourbattery capacity is half or low. Battery indicator on LCD will workonly with Ni-MH type.
The kit compatible with many popularGeiger tubes, such as SBM-20, SBM-19, SI-29BG, SI-180G, SBT-9,SBT-11, J305 and more 400V tubes. When it tuned to 500V you can useLND-712, LND-7317 or similar.
Current radiation dose in uSv/h oruRn/h units represented on LCD with CPM (counts per minute) readings.You can switch between LCD units with pressing \"down\"button. If you press \"up\" button, it will shows clock forseveral seconds, like a digital watches. RTC needs 3V backup batteryCR1220.
Adafruit GPS module can be connected toRX TX pins and selected through sketch settings during firmwareuploading. If no GPS presented, you can use RX TX pins for UARTlogging. CPM value logged through UART to our \"Radiation Logger\"Windows program. When connected to computer, the kit can be used asnuclear radiation monitoring station for local logs, radmon orxively. It possible to separate SD Shield from the Main Board if kitused only for UART logging.
Fast bargraph on LCD for search moderepresent CPS (count per second) measurement. The scale controlledthrough arduino sketch.
The counter has smart LCD backlightcontrolling for saving battery. Backlight will light on when CPMvalue reach presetted alert threshold or if you press any button.Alert BL pin is combined with LCD backlight and can be connected toadditional alert led or drive relay module.
The kit produce clicker sound beepssimilar to \"classic\" Geiger Counter sound. You can mutebuzzer with jumper removed. If radiation level is high, the kitinform you with additional sound indication.
Arduino software developer can modifydefault supplied sketch.
Arduino sketch download link, allrequired libraries link and printed electrical circuit supplied tothe buyer. Please download assembling manual with part list andsoldering steps:
DOWNLOADUser Manual PDF
RadiationLogger Software (requireUART TTL Module)
this video demonstrate two models: RH-K-GK-1-A and RH-K-GK-1-L, please consider the sku number you purchase. This listing is for RH-K-GK-1-L
Main Board Package include:
1x High Quality Manufactured PCB
1x Atmega-328 Microcontroller with bootloader
1x LCD Module 16x2 Green Color
1x CR1220 3V Battery for RTC
1x 100R ohm Resistor
1x 220R ohm Resistor
2x 1K ohm Resistor
3x 10K ohm Resistor
1x 4.7M ohm Resistor
1x 10K Potentiometer
1x 1K Potentiometer
4x 100nF Ceramic Capacitor
1x 300pF Ceramic Capacitor
2x 22pF Ceramic Capacitor
1x 10nF 1000V Ceramic Capacitor
3x 100uF Electrolytic Capacitor
1x 1N4937 Diode
1x LED 3mm
1x MPSA44 High Voltage Transistor
2x 2N3904 Transistor
1x 100uH Axial Inductor
1x 10mH Radial Inductor
1x 16.000 MHz Crystal
1x 28 Pin IC Socket
1x Slide Switch On/Off
2x Tact Switch Side Right Angle
1x Terminal Block
1x Battery Connector Set
2x 6 Pin Female Header
1x 6 Pin Male Header Right Angle
2x 6 Pin Male Header Long
2x Standoffs for LCD
4x Screws for LCD
SD Shield Package Include:
1x High Quality Manufactured PCB
2x 2.2K Resistor SMD 1206
1x 10K Resistor SMD 1206
3x 100nF Capacitor SMD 1206
1x 10uF Capacitor SMD Tantalum
1x 100uF Electrolytic Capacitor
1x BC847 Transistor SMD SOT-23
1x LM1117 3.3V Regulator SMD SOT-223
1x DS1307 RTC SMD SOIC 8
1x 74HC4050 SMD SOIC 16
1x 32.768KHz Crystal
1x Micro SD Socket SMT
1x CR1220 Socket
2x 3 Pin Female Header Connector
1x 4 Pin Female Header Connector
1x 6 Pin Female Header Connector
1x Piezo Buzzer
1x Jumper Cup
4x Standoff for PCB
4x Screws for PCB
The kit’s hardware needs 4.6V-5.4V tooperate when it drawn 20mA without LCD backlight. There is severaloptions for powering the kit, please consider the best for you.Battery indicator in software will work only with Ni-MH batteries.
1. 4x AA 1.2V Ni-MH rechargeablebatteries, 1800mAh or higher.
2. 2x AA 1.5V Alkaline batterieswith 5V step-up module.
3. 3.7V LiPO battery with 5V step-upmodule, 1000mAh or higher.
4. 5V DC regulated power supply forindoor.
Purchase terms:
If you purchase this item you are agreethat you have skills and tools to perform required DIY soldering (orde-soldering) and you know how to connect additional externalcomponents or modules. All project components should be installed andsoldered in proper polarity with proper connectors. Anyhardware/software modifications made by buyer are not covered withwarranty. If you have doubt it always better to ask for technicalsupport before doing something.
Please readcarefully product title, description and include list. Any questionsare welcome.
Please download and read carefully PDF user manual, product purchase terms and almost all technical issues already described in the manual!
If you received broken or defectiveparts please contact me first, because I can resolve this problem inbest way.
Payment: Paypal only, or cash for localpickup.
Best Offer: Please do not send me \"BestOffer\" for one pcs of the kit, it will be declined. I acceptbest offer only for 5pcs or more. Thank you.
Handling time: 3 business days to process international orders required after receiving cleared payment. This does not include the number of business days the shipping service will take to deliver the item to you.
Shipping&Tracking: We dispatch your order during 1-3 business day and will upload a tracking number to for USA buyers only. Take note, international shipping is more complicated and longer than domestic, that\'s why when you buy internationally it mean you are agree to wait for the package. For Economy International Delivery stated times is 3-5 weeks bydefault. Some countriesmay take longer because of your country custom regulation rules or postal service. USA usually take 2-4weeks; Europe 1-4 weeks; Australia 2-4 weeks; Germany 3-4 weeks; Israel 3-7 days;Russian Federation 4-8 weeks or longer; All other countries 3-5 weeksdefault delivery time. Please contact us if you not received your package during 30 days.
Take note, we ship through state export account and not from post office branch. This is the reason why your package is trackable only after it was sent abroad from Israel and not at the date of collecting or at the date we uploaded a tracking number. Online tracking system also displays information with BIG delays, Israel Post website provide tracking info for reference only several days after your item was sent abroad! Please be patient for the delivery and contact us if you have additional questions about shipping. United States, United Kingdom, Canada and Germany allowed to select International Priority Mail 10-14 business days for additional 15.00$ Please select this method if you need faster delivery.Don\'t buy/offer if you are not ready to wait for the package during 3-5 weeks! Don\'t buy/offer if you make low DSR response because of shipping time for Economy International Shipping or because of your custom import tax!Custom & Duty Fee: All international buyers are responsible to cover any possible custom fee or import tax that maybe applied at his/her country. We are obligated by export law of Israel to declare an order price as it was stated in your PayPal bill. German buyers, please remember when you buy that in Germany import custom rules require you to pay fee. We are not accept any claim because of your country custom regulation rules / delays / fee! Please contact your local custom office for more details about custom process and import tax.
Returns: Accepted if you not started tosolder/use device. In original package, including all components.During 14 days after you receive the package.
Technical Support: If you have any technical issue with the product please contact us asap. Support provided byemail or via message. Please readsupport requirements here style=\"margin-bottom: 0cm\">
2013 Year RH Electronics Customers LocationThank you for your positive response!