Up for sale is a QSC CX902 power amplifier. This amp features the legendary PowerLight technology that is also used in the popular PLX line. If you look at the specs you will see that the CX902 is essentially a PLX3002 with slightly different features/connections. Pictures are of the exact amp that you will receive. It is tested and guaranteed to work properly. This unit has some rack rash, dings, and scratches as shown in the pictures, but the front panel looks very clean and the front rack ears are in perfect shape. It comes with the security plate (covers gain adjustments) installed - requires a hex key to remove.Features and specifications:
- Exclusive PowerLight switch-mode power supply technology for high performance and compact size
- Custom integrated security cover for tamper proof installations
- Variable speed fan for low noise
- 1-dB detented gain controls for fast and accurate gain settings
- Active inrush limiting eliminates AC inrush current, removing the need for expensive power sequencers
- XLR and detachable Euro style input connectors
- HD15 DataPort connector for Q-SYS networked control and monitoring
- Dip switch control for clip limiters, high pass filters, bridge mono and parallel operation
- Selectable high pass filters protect speakers and prevent speaker transformer saturation with minimal effect on program material (33 Hz or 75 Hz)
- Comprehensive front panel indicators including signal, clip, protect and QSC\'s exclusive bridge mono and parallel input LEDs
- Barrier strip output connector
- Comprehensive protection circuitry including DC, infrasonic, thermal overload and short circuit protection
- Class H complementary bipolar output circuitry for high efficiency
- Optional external transformer accessory pack for isolated 25-, 70-, and 100-volt outputs
- Compact size - only 2 rack units high and 14\" deep for reduced rack cost and floor space
- Lightweight - weighs only 21 pounds (9.5 kg) for easier racking and shipping
- 3-year warranty plus optional 3-year extended service contract
- All CX Series amplifiers meet the European Union\'s 2006 RoHS directive to restrict the use of hazardous materials used in electronic devices.
SPECIFICATIONS
CX902
POWER PER CHANNEL, STEREO MODE, Both Channels Driven 8Ω, 20 Hz–20 kHz, 0.05% THD
550 W
4Ω, 20 Hz–20 kHz, 0.05% THD
900 W
2Ω, 1 kHz, 1% THD
1500 W
70V, 20 Hz–20 kHz, 0.05% THD
400 W
70 V, 1 kHz, 0.05% THD
440 W
70 V, 1 kHz, 1% THD
600 W
POWER, BRIDGED MONO MODE 16Ω, 20 Hz–20 kHz, 0.1% THD
1100 W
8Ω, 20 Hz–20 kHz, 0.1% THD
2000 W
4Ω, 1 kHz, 1% THD
3000 W
140 V, 20 Hz–20 kHz, 0.05% THD
800 W
140 V, 1 kHz, 0.05% THD
880 W
140 V, 1 kHz, 1% THD
1200 W
Noise, 20 Hz–20 kHz
-106 dB
Input Sensitivity @ 8 ohms
1.17 Vrms
Maximum Voltage Gain
35 dB
Output Circuitry Class
H, 2-tier
ALL MODELS Distortion (SMPTE-IM) Less than 0.02% Distortion (Typical)
20 Hz–20 kHz: 10 dB below rated power
1.0 kHz and below: full rated power
Less than 0.01% THD
Less than 0.01% THD Frequency Response 20 Hz–20 kHz, ±0.2 dB Damping Factor Greater than 500 Input Impedance 6 kΩ unbalanced, 12 kΩ balanced Input Clipping 10 V rms (+22 dBu) Cooling Variable-speed fan, rear-to-front air flow Connectors, each channel Input: 3-pin XLR & 3-pin detachable terminal blocks (1 each per channel)
Output: Safety-shrouded barrier strip Amplifier Protection Full short circuit, open circuit, thermal, ultrasonic, and RF protection.
Stable into reactive or mismatched loads. Load Protection On/off muting, DC-fault power supply shutdown Dimensions (HWD) inches 3.5 x 19 x14 / 2RU Dimensions (HWD) mm 89 x 483 x 356 / 2RU Weight 21 lb (9.5 kg) net
27 lb (12.3 kg) shipping